Pneumatic immersion separator for combustible metal powder – venturi drive without an electric motor, collection straight into a water bath, CFE coalescing filter of HEPA grade, SS304 tank and four-wheel dolly. Marked II 2GD to EN 17348 WT
The Tiger-Vac ATEX-10A (IT-40L) CFE HEPA is a pneumatic immersion separator – a vacuum where the recovered powder does not land in a dry container but is drawn straight down into a water bath. Tiger-Vac describes the principle as recovery and inertisation of combustible dust into a liquid immersion bath: as long as the particles stay wetted they cannot form a dust cloud. The machine is driven by compressed air through a single venturi and has no electric motor, so it can run continuously without overheating or wear. It needs a compressor of at least 15 HP, a 1/2″ (12.7 mm) air line and 5.5 bar; the pressure regulator is included and factory set to 5.5 bar. Performance is 187 m³/h at 2790 mmH₂O, but depends on the capacity of the compressor. This model is intended for water (not oil) and needs 12.3 L of water in the recovery tank before use. Collection itself happens in a conductive disposable wet bag rated at 3 L. A degassing vent releases gas from the unit automatically, and a liquid level indicator with drain valve lets you check the bath without opening the tank. CFE stands for Coalescing Filter Element – a coalescing filter that strips moisture from the outgoing air and filters at HEPA grade, which Tiger-Vac states as 99.97 % at 0.3 micron. According to Tiger-Vac the machine meets the requirements for a liquid precipitation collector for metal dusts in NFPA 484. The tank is AISI 304 stainless steel and the machine stands on a four-wheel dolly. It is available with the standard tool kit (part no. 113116) or with a 3D tool kit for print chambers and powder handling (113116-3D).
| ATEX marking | II 2GD Ex h IIC T6 Gb – Ex h IIIC T85 °C Db – 0 °C <= Ta <= +40 °C – LCIE 16 AR 077 (Annex VIII) – EN 17348 WT |
|---|---|
| Internal / external zone | None / 21 (dust) and 1 (gas) |
| Motor type | No motor – pneumatic operation with a single venturi, no electrical parts |
| Duty cycle | Continuous |
| Airflow | 187 m³/h |
| Vacuum | 274 mbar (2790 mmH₂O) |
| Container | 3 L |
| Sound pressure | 68 dB(A) |
| Filter class | H class |
| Filter type | CFE coalescing filter element, HEPA grade – Tiger-Vac states 99.97 % at 0.3 micron |
| Primary filter | Liquid bath (immersion) – the powder is collected wet in a conductive disposable bag |
| Cleaning system | Liquid bath – no dry filter cleaning; the bath is changed together with the wet bag |
| Collection system | Water bath in SS304 tank with conductive disposable wet bag |
| Material | AISI 304 stainless steel |
| Drive type | Pneumatic – single venturi |
| Minimum compressor | 15 HP |
| Compressed air | 5.5 bar · 16.5–21.2 L/s |
| Air connection | Ø 12.7 mm (1/2″) |
| Inlet | Ø 38 mm |
| Dimensions (L × W × H) | 480 x 460 x 860 mm |
| Weight | Available on request |







Because dry metal powder in air is among the most dangerous combustible dusts there is. Aluminium, titanium and magnesium have low minimum ignition energy, and a dry container full of fine metal powder is effectively an explosive chamber waiting for an ignition source. In an immersion separator the powder is drawn straight into a liquid bath. The particles are wetted and cannot form a dust cloud – and without a dust cloud there is no dust explosion. Tiger-Vac calls the principle inertisation in a liquid bath. The ATEX-10A runs on water only (not oil), and some reactive metals react with water. If you are unsure what your powder tolerates, talk to us before choosing a model.
EN 17348:2022 is the product standard for vacuum cleaners used in explosive atmospheres. It classifies machines by how the collected dust is handled. DT means dry type – dry collection in a container or bag. WT means wet type – wet collection, where the dust is held in a liquid. This model is WT, and that is not a detail: the classification says the machine is designed and tested specifically to keep combustible dust wet, not to collect it dry. A DT machine must therefore not be substituted for reactive metal powder, even if it carries the same ATEX marking.
Both are immersion separators with a water bath, a CFE coalescing filter of HEPA grade, an SS304 tank and II 2GD marking. The difference is the drive. The ATEX-10A is driven by compressed air through a venturi and has no electrical parts; it can run continuously but needs a compressor of at least 15 HP at 5.5 bar. The EXP1-10 has a single-phase TEFC electric motor and needs 230 V instead. Choose the ATEX-10A where there is enough compressed air and you would rather avoid electrical parts in the zone.
The marking is II 2GD, that is ATEX category 2 for both gas and dust externally (Ex h IIC T6 Gb / Ex h IIIC T85 °C Db). Specifically the unit may be placed in Zone 1, where an explosive gas atmosphere is likely to occur in normal operation, and in Zone 21, where the same applies to explosive dust. Ambient temperature must be between 0 °C and +40 °C. The machine does not carry a separate internal Zone 0/20 marking; internal safety rests on the liquid bath.
The ATEX-10A comes in two versions with the same machine and performance. The standard version (113116) ships with a static-dissipative tool kit for the 1.5″ camlock inlet: suction hose 3 m, air supply hose 7.5 m with quick disconnects, two-piece stainless steel wand, universal tool with conductive brush strips and rubber blades, conical nozzle, Tiger Claw, round brush and a multimeter. The W/3D TOOL KIT version (113116-3D) ships with a 3D tool kit for the 1.5″ camlock inlet, intended for print chambers and powder handling, and optional 3D tools are available for it. Both stand on a four-wheel dolly.